Description
- Fitment: Fit 2019 2020 2021 2022 2023 2024 2025 Chevrolet Silverado /GMC Sierra 1500 5.8’/69.9″ Bed. Xcover is Low Profile and sit inside of truck bed, full stake pockets available to be used with the cover on.
- Well Protect Your Cargos: Xcover Low profile Hard fold tonnneau cover is designed to perform in the most extreme conditions,premium UV resistant and cold resistant, no matter snowy, rainy, windy or sunny, your cargos on the bed will be well protected from moisture and dirt.
- Unique Clamping System & Theft Protection: Patent pending rail and latch design, Xcover latch allows for one-finger release to open and locks automatically when you close the cover. Hard Panel is scratch resistant and provides maximum theft protection.
- Durable & Easy Installation: Solid Core Hard Panels can be rated up to 500lbs of evenly distributed weight. Please see the video on the left for installation , it is completely assembled for easy No-Drilling installation in minutes. ATTENTION: Make sure the Flat Washer and Spring Washer are all placed on bolt before screw the plastic nut on. TIGHTEN ALL BOLTS & NUTS BEFORE DRIVING!
- 5 Years Warranty: Against defects in materials and workmanship under its intended use, Please be assured to use our tonneau cover. Any bolts or mounting hardware need the replacement, any questions, please contact our customer service. WARNING: Always make sure the clamps and bolts are tightened before driving, never drive with a cover in partially opened position.
![AmeriLite for 2014-2016 GMC Sierra 1500 2500HD 3500HD [Halogen Type] LED Bar Projector Black Headlights Assembly Pair - Driver and Passenger Side](https://rentatrucknearme.com/wp-content/uploads/2025/01/amerilite-for-2014-2016-gmc-sierra-1500-2500hd-3500hd-halogen-type-led-bar-300x300.jpg)
Benjmain Dieringer –
Very easy install, very sturdy tracks, low profile and perfect for for a 2024 1500 LT ZR1 trail boss. I tried another low profile trifold truck bed cover but it was flimsy and difficult to install. This was great!!
Dean Ruscoe –
We were searching around to see how much it would cost us to get a cover for our truck bed and as much as we wanted it and needed it, over $1500 seemed like a lot to us. Found this one with good reviews and decided to go for it since it didn’t look so hard to do ourselves. Best decision! Not only did we get it for half the price but the install was super easy, had it done in about an hour and it looks great!!!
Paul A Harper –
Looks great fit perfect. It was easy to install great value for the price looks like 1 million bucks. I would order this again for sure. The durability seems good so far. It’s been on my truck for three months.
L Smith –
I put this cover on my 2023 sierra short bed. It’s been on the truck for about 4,000 miles now. It took me almost 2 hours to install. It’s not difficult to install. The directions aren’t great and the parts (left right front back) weren’t marked. After I put it on I told my wife it would be a miracle if it didn’t leak. It hasn’t leaked yet and its been through plenty of rain. It’s super low profile and the center pull line makes it easy to open and close securely. Nothing like my previous cover where I was always trying to get the plastic levers to lock or unlock without breaking them. I don’t know what the weight limit is but it’s definitely a heavy duty top.
Kellen R Godfrey –
Fair price and fits perfect. Engineered quite well and the hardware is too. Installation, using the instructions are less than ideal and pictures, in some cases aren’t beneficial. I purchased 1/4”x1/4”x26’ foam stripping to reduce water intrusion. For drain, my 2024 GMC Sierra holes were not big enough for drain tubes, so I used an adapter hose & RTV to connect the two to avoid drilling bigger holes. The cover looks great and is sturdy. I gave it 5 stars because the quality for the price is worth it. If you use something like YouTube and not solely the instructions the average DIY can do this in less than 90 minutes. This is my first time, so I took my time. Now that I did it once, piece of cake the next. I would buy this again!
Benjmain Dieringer –
This tonneau cover is great so far. I’ve had it installed on my 2020 Sierra SLT for a few weeks, and I am very satisfied with the purchase, especially for the price. On the positive side, it fits very tight and secure. While it’s not as low-profile as other low-profile covers (it sits slightly above the edge of the box), it still looks very good and serves its purpose. It can also be removed fairly easily if needed.
On the negative side, the instructions are very difficult to follow. It’s very unclear “what goes where”, but once you figure it out, it’s a fairly simple install. Also, it’s not 100% water tight. I get a bit of leakage into the bed around the corners, but nothing too bad.
Helpful tip: make sure you position the tonneau cover in the right position for optimal function. I’ve seen some reviews saying the cover won’t allow the auto tailgate to open, or you can’t lock it into position with the tailgate closed. As long as you position the cover closer to the bulkhead and don’t cover half of the tailgate door, neither of these functions will be effected.
Kellen R Godfrey –
I brought this cover in July for my 2024 GMC, Sierra, reviews looked good, low profile
Arrived quickly, easily to install, looks great
After having the cover for 2 months I noticed the glue coming unstuck on the rubber seals along the side, which kind of ruined the integrity of the cover, so I called Amazon, they couldn’t help, they gave me a number to xcover, which was just a number that directed you to a website, go to the website and there is only an email, sent the company an email and no response.
After looking online, a lot of people say the xcover warranty is a scam and the can’t get anywhere with them, I have lost hope that the cover I brought will be fixed. Avoid if possible.
AMOPFL –
I installed in less than an hour and all by myself. The instructions were a little difficult to follow. I’m hoping the pictures I included will help others. I used a rubber mallet to get the drain tube into the end of the rail. When installing the clamp at the front, I put the clamp between the front end and the clamp that holds the cover to the rail. Before tightening the bolt that holds the cover to the frame, I aligned the cover so that it was square on the bed. Don’t move the cover until you have tightened the bolts. It also works with my assist bar. The multi-pro tailgate does not go down automatically because I have the cover tight against the top. So I just give the tailgate a little tug and it opens. The sides are very secure, but the latch release in the back can easily be opened if you have something flat that can slip between the tailgate and cover and be used to pull the cable.
Update on this cover. After a few months, the hard rubber blocks that stick to the bottom of the cover (used when folding the cover up to keep it in the right position and from scratching) will not stay on. I think the summer heat softened the double stick tape. Also the rubber strip that is on each side rail has also come loose, the double stick tape again lost its stick. On a good note, it has not leaked yet.